Free shipping on orders $149 & up. exclusions apply

Swivel Fittings, 1-1/2"


Swivel Fittings, 1-1/2"

Category: Swivel Manifold

Available ModelsPartPrice
SWF014 : Swivel Tee 1-1/2 in.  FPT with O-ring x 1-1/2 in.  FPT with O-ring x 1-1/2 in.  MPT Swivel Tee 1-1/2" FPT with O-ring x 1-1/2" FPT with O-ring x 1-1/2" MPTSWF014$3.99 $1.76
clearance item 7 left
SWF015 : Swivel Adapter 1-1/2 in.  MPT x 1-1/2 in.  FPT with O-ring Swivel Adapter 1-1/2" MPT x 1-1/2" FPT with O-ringSWF015$2.84 $2.13
clearance item 16 left
SWF016 : End Cap 1-1/2 in.  FPT with O-ring End Cap 1-1/2" FPT with O-ringSWF016$0.81 $0.47
clearance item 64 left
SWF017 : Nipple 1-/2 in.  MPT x 1-1/2 in.  MPT with O-ring Nipple 1-/2" MPT x 1-1/2" MPT with O-ringSWF017$1.28 $0.69
clearance item 53 left

The Drip Store’s high pressure swivel fittings are used for assembly of valve manifolds and valve zones without using glue or tools. Each of the fittings has a large swivel with female thread and encapsulated large "O" ring to ensure a watertight connection. The design allows for quick connection of valves without Teflon tape. Use this line of fittings to make a 3/4”, 1”, 1-1/2” or 2” valve manifold with the correct spacing between the valves, as a union or for any type of assembly that needs a quick connection.

  • Inlet and outlet
    • SWF014, SWF015, SWF016, SWF017 : Inlet thread: swivel FNPT with encapsulated "O"
    • SWF014, SWF015, SWF016, SWF017 : Outlet thread: MNPT
  • Materials
    • SWF014, SWF015, SWF016, SWF017 : Body and swivel: polypropylene with UV
    • SWF014, SWF015, SWF016, SWF017 : O-ring: nitril rubber
  • Operating pressure
    • SWF014, SWF015, SWF016, SWF017 : up to 120 PSI
  • Temperature range
    • SWF014, SWF015, SWF016, SWF017 : Up to 130°F
  • Secure and easy installation without glue or tools
  • The swivel fitting can be used as a union for quick removal of a valve
  • The swivel fittings are available with a 1”, 1-1/2” and 2” swivel
    • Installation for Valve Manifolds

      Example: A valve manifold starting from a 1” PVC pipe:

      1.      Glue to the PVC pipe a PVC adapter with 1” MPT

      2.      Connect a swivel manifold with 1, 2, 3 or 4 outlets depending on the number of valves in the manifold.

      3.      To the outlet side of the valve with the swivel connect a PVC male adapter

      4.      Glue the PVC pipe to the male adapter

      5.      Turn the water on and flush the line

      6.      Close the end of the manifold using the end cap (model SWF006, sold separately)

      7.      Pressurize the system and make sure that water is not leaking from the unit or any part along the line. Test the assembly manually and then automatically via the controller, and then program the controller.

      Note: Make sure that the water flow direction matches for each component, if any is in line with the water flow. Use Teflon Tape only with the PVC male adapter and make sure to remove all Teflon tape excess.

      Valve Manifold, 3-way swivel manifold