Free shipping on orders $149 $99 & up. exclusions apply

Micro Sprinkler Irrigation Kit with 200’ 1/2" Drip Tubing Model K020


Micro Sprinkler Irrigation Kit with  200’ 1/2 in.  Drip Tubing Model  K020
In Stock

The K020 Mini Sprinkler Irrigation Kit with 10, 15 GPH micro sprinklers with 360-degres is The Drip Store’s custom designed kit that contains 200’ of high quality 1/2" drip hose with .600 ID x .700 OD and all the parts needed to install and complete a micro sprinkler irrigation system. This micro sprinkler kit includes a wide range of components used to install a micro sprinkler irrigation system capable of watering a row of trees, flowerbeds or for dust control in a site up to 1000 SF.

Part #: K020
$67.94 ea.

See Added Parts to expand your system by purchasing additional pieces separately.

The watering components include 10, 15 GPH each pre-assembled mini sprinklers with 360-degree. In addition the kit includes a wide range of components used to install a mini sprinkler irrigation system capable of watering a row of trees, flowerbeds or for dust control in a site up to 1000 SF. The irrigation kit can accommodate expansion up to 2000 SF using additional drip hose and micro sprinklers.

The model K020 Mini Sprinkler Irrigation Kit is a complete kit that has all the parts needed to install a micro sprinkler system from a hose faucet (spigot).

Suggestion in connecting the 1/2" compression drip fittings. To install the 1/2" compression fittings, cut the drip tubing with a hand pruner, being careful to keep dirt from entering the line. Hold the compression fitting in one hand and the drip tubing in the other and force the drip tubing into the fitting by wiggling it from side to side. Make sure that the drip tubing is pushed into the compression fitting for about 1/2 to 5/8 of an inch for a very tight fit. No glue or clamps are required.

  • Flow rate: 15 GPH
  • Maximum incoming operating pressure: 100 PSI
  • Operating pressure: 25 to 30 PSI

Installation for K020

 

This micro sprinkler kit has all the parts needed to start the system connecting to a faucet.  The Drip Store also includes instructions on how to start the irrigation system from a PVC pipe or a pipe thread.

Starting the system from a faucet:

  • Optional: If you wish to automate the irrigation system, first connect a battery-operated timer to the faucet (suggested model C001 - not included in this kit).
  1. Connect the 3/4" FHT x MHT backflow device to the controller or to the faucet if not used with a controller (model A015).
  2. Connect the 3/4" FHT x MHT filter (model F300) to the backflow device if used, or directly to the controller male outlet or faucet.
  3. Connect the 3/4" FHT x MHT pressure regulator (model A013) to the filter.

Optional: Starting the system from a PVC pipe:

  1. Glue to a 3/4" PVC pipe a PVC adapter (model P357) (not included).
  2. Use the 3/4" MHT x MPT nipple (model A010) to connect to the pipe thread making sure to use 3-5 rounds of Teflon tape.
  3. Connect the 3/4" FHT X MHT battery-operated controller (model C001) (not included) to the nipple.
  4. Connect the 3/4" FHT x MHT backflow device (model A015) to the controller (not included), or to faucet.
  5. Connect the 3/4" FHT x MHT filter (model F300) to the backflow device, if used, or directly to the controller male outlet or faucet.
  6. Connect the 3/4" 25 PSI FHT x MHT pressure regulator (model A013) to the filter.

Steps to connect all others components:

  1. To the 3/4" FHT x MHT pressure regulator connect the 3/4" FHT swivel adapter (model LF503).
  2. Use the 1/2" elbow (model LF007) as needed.
  3. Use 1/2" coupling .700 O.D. (model LF001) to connect additional 1/2" drip tubing, or for repair.
  4. Use the 1/2" tee (model LF005) to split the 1/2" drip tubing in three directions or to make a loop around a tree (if needed).
  5. Use the 1/2" elbow on corners or for a 90 degree layout (if needed).
  6. Turn the water on and flush the line, and then close the end of the 1/2"drip tubing (model T0060) using hose end (model A006).

Micro/mini sprinklers have small droplets and a low flow application rate. Micro/mini sprinkler irrigation can prevent plant stress by maintaining low water tension in the soil using a low flow application rate. Use the micro/mini sprinklers to water individual trees, flowerbeds, or areas where drippers are not practical, such hillsides, or when low volume, overhead irrigation is desired. Like the drippers, the micro/mini sprinklers operate at low pressure but have a larger range of flow rates and diameters.

  1. Install the mini sprinkler (model MSA037) one per tree and about 1 foot from the tree trunk or every 6’ if full coverage is required
    1. First, punch a hole in the drip hose and insert the 1/4" barb on the mini sprinkler assembly into the drip hose. Place the stake assembly 6-8” above the ground.
  2. Use the punch (model A019) to punch hole in the 1/2" drip tubing for the insertion of the drippers and 1/4" fittings if needed.
  3. The 1/2" stake (model S006) is used to secure the 1/2" drip hose to the ground. Place every 4' to 6' apart or as needed.
  4. Use goof plugs (if needed) (model SF007) to repair small holes in the 1/2" drip tubing. The goof plug may also be used to close the end of the 1/4" micro tubing.

 

Note: The pressure regulator (included) is used to lower the incoming pressure to the suggested operating pressure of 25 PSI, which is within the range of recommended pressures for a drip system or micro-sprinkler system.

How much time to water:  Turn the water onfor 45 minutes to 1 hour every two days, depending on your location and the soil type.  After a week or two check the soil and the health of the plants, and adjust the irrigation time as needed.  If you have a controller and you need to add more time, adjust the time on the irrigation controller or program the controller with additional start-times.

Kit QtyPart #ImageDescription
6A006A006 :  Figure “8” Hose End for 1/2” Drip Tubing  Figure “8” Hose End for 1/2” Drip Tubing
1A010A010 : 3/4” MPT x  3/4” MHT Nipple 3/4” MPT x 3/4” MHT Nipple
1A013A013 : 3/4 in.   FHT Basic Pressure Regulator, 25 PSI 3/4" FHT Basic Pressure Regulator, 25 PSI
1A015A015 : Backflow Preventer 3/4 in.  FHT x  3/4 in.  MHT Backflow Preventer 3/4" FHT x 3/4" MHT
1A019A019 : Palm Hole Punch Palm Hole Punch
1F300F300 : 3/4 in.   in. Y in.  Style Filter with Hose Threads, 155 mesh, polyester screen, green 155 mesh, polyester screen, green3/4" "Y" Style Filter with Hose Threads, 155 mesh, polyester screen, green
5LF001LF001 : 1/2 in.  .700 OD Compression Coupling  1/2" .700 OD Compression Coupling
5LF005LF005 : 1/2 in.  .700 OD Compression Tee  1/2" .700 OD Compression Tee
5LF007LF007 : 1/2 in.  .700 OD Compression Elbow  1/2" .700 OD Compression Elbow
1LF503LF503 : 3/4” FHT x .700 O.D. Swivel Adapter with Washer  3/4” FHT x .700 O.D. Swivel Adapter with Washer
10MSA037MSA037 : Mini sprinkler assembly with spinner/nozzle gray 15 GPH Mini sprinkler assembly with spinner/nozzle gray 15 GPH
30S006S006 : 5” Hold Down Stake for 1/2” Drip Tubing 5” Hold Down Stake for 1/2” Drip Tubing
2SF007SF007 : Goof Plugs, Strip of 10  Goof Plugs, Strip of 10
1T060T060 : DIG Corporation Drip Tubing, 200 ft. , 1/2 in.  coil  with .700 OD 200 ft. , 1/2 in.  coil  with .700 ODDIG Corporation Drip Tubing, 200’, 1/2" coil with .700 OD
KIT K020 contains a total of 70 pcs. for $67.94
ImageDescriptionPart #PriceQty.
A006 :  Figure “8” Hose End for 1/2” Drip Tubing  Figure “8” Hose End for 1/2” Drip Tubing A006$0.13 ea.
A010 : 3/4” MPT x  3/4” MHT Nipple 3/4” MPT x 3/4” MHT NippleA010$0.55 ea.
A013 : 3/4 in.   FHT Basic Pressure Regulator, 25 PSI 3/4" FHT Basic Pressure Regulator, 25 PSIA013$5.59 ea.
A015 : Backflow Preventer 3/4 in.  FHT x  3/4 in.  MHT Backflow Preventer 3/4" FHT x 3/4" MHTA015$3.11 ea.
A019 : Palm Hole Punch Palm Hole PunchA019$1.74 ea.
F300 : 3/4 in.   in. Y in.  Style Filter with Hose Threads, 155 mesh, polyester screen, green, 155 mesh, polyester screen, green 155 mesh, polyester screen, green3/4" "Y" Style Filter with Hose Threads, 155 mesh, polyester screen, green, 155 mesh, polyester screen, greenF300$9.50 ea.
LF001 : 1/2 in.  .700 OD Compression Coupling  1/2" .700 OD Compression Coupling LF001$0.48 ea.
LF005 : 1/2 in.  .700 OD Compression Tee  1/2" .700 OD Compression Tee LF005$0.72 ea.
LF007 : 1/2 in.  .700 OD Compression Elbow  1/2" .700 OD Compression Elbow LF007$0.69 ea.
LF503 : 3/4” FHT x .700 O.D. Swivel Adapter with Washer  3/4” FHT x .700 O.D. Swivel Adapter with Washer LF503$0.93 ea.
MSA037 : Mini sprinkler assembly with spinner/nozzle gray 15 GPH Mini sprinkler assembly with spinner/nozzle gray 15 GPHMSA037$1.01 - $1.34 ea.
S006 : 5” Hold Down Stake for 1/2” Drip Tubing 5” Hold Down Stake for 1/2” Drip TubingS006$0.28 ea.
SF007 : Goof Plugs, Strip of 10  Goof Plugs, Strip of 10 SF007$0.25 - $0.29 ea.
T060 : DIG Corporation Drip Tubing, 200 ft. , 1/2 in.  coil  with .700 OD, 200 ft. , 1/2 in.  coil  with .700 OD 200 ft. , 1/2 in.  coil  with .700 ODDIG Corporation Drip Tubing, 200’, 1/2" coil with .700 OD, 200’, 1/2" coil with .700 ODT060$21.87 ea.