12" Pop-Up Micro Sprayers

Available Models		Part	Price
	360° Pop-Up Micro Sprayer with 1/2” MPT	MP001	$4.84 ea.
2 reviews	180° Pop-Up Micro Sprayer with 1/2” MPT	MP002	$4.87 ea.
	90° Pop-Up Micro Sprayer with 1/2” MPT	MP003	$4.91 ea.
	90° Pop-Up Micro Sprayer with 24” Micro Tubing and Barb	MP004	$4.35 ea.
	180° Pop-Up Micro Sprayer with 24” Micro Tubing and Barb	MP005	$4.38 ea.
	360° Pop-Up Micro Sprayer with 24” Micro Tubing and Barb	MP006	$4.41 ea.

Description
Specifications
Features
Instructions

The 12" spring loaded pop-up micro sprayers from DIG Corporation are designed to provide solutions where low pressure and low application rate are preferred. The pop-up micro sprayers incorporate a pressure activated low friction, upper stem seal and a second stage piston seal to insure positive sealing and operation reliability and long-term performance. The pop-up micro sprayers are helpful where conventional sprinkler systems or drip irrigation would not be practical and the drip tubing is covered. The pop-up micro sprayers present advanced features and proven technology used with low flow for an efficient and consistent micro irrigation system.

Available

MP001, MP002, MP003, MP004, MP005, MP006 : with 1/2" NMPT or assembled with 24” micro tubing and 1/4" Barb

Available nozzles

MP001, MP002, MP003, MP004, MP005, MP006 : Blue: 90° with 14 GPH @ 30 PSI
MP001, MP002, MP003, MP004, MP005, MP006 : Green: 180° with 27 GPH @ 30 PSI
MP001, MP002, MP003, MP004, MP005, MP006 : Red: 360° with 38 GPH @ 30 PSI

Droplet Size

MP001, MP002, MP003, MP004, MP005, MP006 : Medium

Flow rate

MP001, MP002, MP003, MP004, MP005, MP006 : .15 to .63 GPM

Materials

MP001, MP002, MP003, MP004, MP005, MP006 : Bases: high impact plastic
MP001, MP002, MP003, MP004, MP005, MP006 : Body and piston: Polypropylene
MP001, MP002, MP003, MP004, MP005, MP006 : Seals: EPDM and vinyl
MP001, MP002, MP003, MP004, MP005, MP006 : Spring: Stainless Steel

Nominal operating pressure

MP001, MP002, MP003, MP004, MP005, MP006 : 30 PSI

Operating pressure

MP001, MP002, MP003, MP004, MP005, MP006 : 15 to 35 PSI

Pop-up height

MP001, MP002, MP003, MP004, MP005, MP006 : 12" or when up 21"

Precipitation rate

MP001, MP002, MP003, MP004, MP005, MP006 : 2.0 to 2.8 inch/h

Recommended filtration

MP001, MP002, MP003, MP004, MP005, MP006 : 120 mesh

Trajectory Angle

MP001, MP002, MP003, MP004, MP005, MP006 : Flat

Wetting diameter

MP001, MP002, MP003, MP004, MP005, MP006 : up to 5' radius

12" pop-up assembly

Available with replacement nozzles

Can be installed on any size drip tubing using the micro tubing assembly or mounted to a 1/2" FNPT PVC pipe

Install below grade

Rugged materials can withstand adverse conditions

Rugged materials to withstand the most adverse conditions

Unique design incorporates a pressure activated, low friction, upper stem seal and a second stage piston seal to ensure positive sealing

Installation for Pop-up Micro Sprayers

To install the pop-up micro sprayers use one of the two options:

Installation using drip tubing as the main lateral:

With this layout use the complete assembly pop-up micro sprayers with 24” micro tubing and barb. Install the pop-up by punching a hole into the side of the drip tubing and inserting the 1/4" barb into the drip tubing. Mount the pop-up micro sprayer about 2-4” above the ground with spacing between the pop-ups of up to 5’.

Installation using PVC pipe as the main lateral:

With this layout use the complete assembly pop-up micro sprayers with 1/2" MNPT. Install the pop-up by installing a PVC tee with 1/2" FNPT and then thread the pop-up into the 1/2" outlet. Mount the pop-up micro sprayer about 2-4” above the ground with spacing between the pop-ups of up to 5’.

If using the one piece construction replacement spray head without the pop-up, install the head at the end of a length of 1/4" micro-tubing or use with a semi rigid poly riser.