PC Dripline Irrigation Kit Model K008
This PC Dripline from DIG is an advanced pressure-compensating dripline incorporating PC inline emitters with low-density brown polyethylene tubing. The PC drip emitters have a cylindrical design with turbulent flow. Additionally, they are flow-regulated using a silicon diaphragm and are self-flushing. The PC drip emitters are inserted and welded into the inside wall of the polyethylene tubing in a preset spacing of 18" using a flow rate of 1 gallon per hour (GPH). The efficient design of the PC Dripline makes it a reliable system in a wide range of irrigation applications.
Drip irrigation is the slow application of water directly to the plants' root zone in a predetermined pattern. Maintaining an optimum moisture level in the soil at all times results in less water lost to the sun and the wind. No water is wasted on non-growth areas, and the root zone is maintained at its ideal moisture level, combining the proper balance of water and air for a very efficient irrigation system.
This kit has all the parts needed to implement a drip irrigation system from a hose faucet (spigot) or from an inline valve.
Maximum incoming operating pressure: 100 PSI
Operating pressure: 10-45 PSI
Drippers flow rate: 1gallon per hour (GPH)
Note.
The pressure regulator (included) is used to lower the incoming pressure to the micro sprinklers and drippers to the suggested operating pressure of 25 PSI, which is in the range of recommended pressures for a drip or micro-sprinkler system.
Information that can help in the installation of the system
This drip irrigation kit has all the parts needed to start the system connecting to a faucet. The Drip Store also includes instructions on how to start the system from a PVC pipe or a pipe thread.
Optional:
If you wish to automate the system, first connect a battery-operated timer to the faucet (suggested model C001 - not included in this kit).
Connect the 3/4" FHT x MHT backflow device(model A015) to the controller or to the faucet if not used with a controller.
Connect the 3/4" FHT x MHT filter (model F300) to the backflow device if used, or directly to the controller male outlet or faucet.
Connect the 3/4" FHT x MHT pressure regulator (model A013) to the filter.
Option 2: Requires model P357-not included
Glue to a 3/4" PVC pipe a PVC male adapter (model P357) (not included).
Use the 3/4" MHT x MPT nipple (model A010) to connect to the pipe thread making sure to use 3-5 rounds of Teflon tape.
Connect the 3/4" FHT x MHT battery-operated controller (model C001) (not included).to the nipple.
Connect the 3/4" FHT x MHT backflow device (model A015) to the controller (not included), or to the faucet .
Connect the 3/4" FHT x MHT filter (model F300) to the backflow device, if used, or directly to the controller male outlet or faucet.
Connect the 3/4" FHT x MHT 25 PSI pressure regulator (model A013) to the filter.
To the 3/4" FHT x MHT pressure regulator connect the 3/4" FHT swivel adapter (model LF503), to the adapter connect the poly tubing by wiggling and forcing the drip tubing into the compression side of the adapter and lay out the drip tubing to the garden area. The 1/2" drip tubing is used as the main line to deliver the water to the drip line.
Use the 1/2" elbow (model LF007) as needed.
Use 1/2" coupling .700 O.D. (model LF001) to connect additional 1/2" drip tubing, or for repair.
Used the 1/2" tee (model LF005) to split the 1/2" drip tubing if needed and to connect the drip line into the drip tubing.
Connect the drip line with a dripper every 18" (model DL080) into the drip tubing using the tee and lay out near the plants row.
Turn the water on and flush the line, and then close the end of the 1/2"drip tubing using hose end (model A006).
Use the 1/2" holder stake (model S006) to secure the 1/2" drip tubing and drip line to the ground.
How much time to water:
Turn the water on for 45 minutes to 1 hour every two days, depending on your location and the soil type. After a week or two check the soil and the health of the plants, and adjust the irrigation time as needed. If you have an irrigation controller and you need to add more time, adjust the time on the controller or program the controller with additional start-times.
Supplier: The Drip Store
Part#: K008
Price: $50.33
