Free shipping on orders $149 & up. exclusions apply

180° Pop-Up Micro Sprayer with 1/2” MPT


180° Pop-Up Micro Sprayer with 1/2” MPT
In Stock

The 180-degree, 12" pop-up micro sprayers with 1/2” MPT from DIG Corporation are designed to provide solutions where low pressure and low application rate are preferred. The pop up micro sprayer has a 180° pattern with radius of up to a 5' and a flow rate of 27 GPH @ 30 PSI. The pop-up micro sprayers incorporate a pressure activated low friction, upper stem seal and a second stage piston seal to insure positive sealing and operation reliability and long-term performance. Use these pop-up micro sprayers for ground-cover, flowerbeds and shrubs or where conventional sprinkler systems or drip irrigation would not be practical and the drip tubing needs to be covered.

Part #: MP002
$4.87 ea.
  ( 2 ratings/reviews )

The Drip Store has a wide range of micro sprayers and jets to meet all of today‘s requirements for micro irrigation needs. The no moving parts pop-up micro sprayers can be used for a wide range of applications and are available with 360, 180, and 90 degree pattern with a small diameter and for watering that requires small droplets size with low precipitation rates. When low volume overhead irrigation is desired for an area where drip emitters are not practical and micro sprinkler diameters and moving parts are not required nor preferred, the micro sprayers may be what are needed. Like micro sprinklers, the pop-up micro sprayers and others are available in a wide variety of styles, flow rates, diameters, and configurations. Like micro sprinklers, they operate at low pressure and require a filter to protect the small orifice of the sprayer from clogging. The main advantage of micro sprayers to some users and installers could be the lack of moving parts and the small to medium sized droplets and coverage.

By: herbwhitaker, 05/17/09

Dripcorp replaced all defectiive stems (27) on my original orders of 90 degree, 180 degree and 360 degree Pop-up units. The new units are operational at this date. I appreciate the quick response and plan to purchase several more units in the near future.

Thank You.

By: herbwhitaker, 04/25/09

The pop up stem splits at the point where the nozzle is "threaded" into the stem. The split stems were discovered after installation; however, a few defective split stems were discovered before installation.

I have removed the nozzle on some stems removing the split (cut off about a half inch) and replacing the nozzle. This repair works on a few of the stems... others, it only splits again.

The pop up sprinklers, 90, 180, 360 degrees, is an effective product for low pressure (20-25 psi) irrigation water provided in the city.

Do you know of an effective solution to the above described defect?

  • Available: with 1/2" NMPT or assembled with 24” micro tubing and 1/4" Barb
  • Available nozzles : Blue: 90° with 14 GPH @ 30 PSI, Green: 180° with 27 GPH @ 30 PSI , Red: 360° with 38 GPH @ 30 PSI
  • Droplet Size: Medium
  • Flow rate: .15 to .63 GPM
  • Materials: Bases: high impact plastic , Body and piston: Polypropylene , Seals: EPDM and vinyl , Spring: Stainless Steel
  • Nominal operating pressure : 30 PSI
  • Operating pressure: 15 to 35 PSI
  • Pop-up height : 12" or when up 21"
  • Precipitation rate: 2.0 to 2.8 inch/h
  • Recommended filtration: 120 mesh
  • Trajectory Angle: Flat
  • Wetting diameter : up to 5' radius
  • Available with replacement nozzles
  • Can be installed on any size drip tubing using the micro tubing assembly or mounted to a 1/2" FNPT PVC pipe
  • Install below grade
  • Rugged materials can withstand adverse conditions
  • Unique design incorporates a pressure activated, low friction, upper stem seal and a second stage piston seal to ensure positive sealing

Installation for Pop-up Micro Sprayers

To install the pop-up micro sprayers use one of the two options:

Installation using drip tubing as the main lateral:

With this layout use the complete assembly pop-up micro sprayers with 24” micro tubing and barb. Install the pop-up by punching a hole into the side of the drip tubing and inserting the 1/4" barb into the drip tubing. Mount the pop-up micro sprayer about 2-4” above the ground with spacing between the pop-ups of up to 5’.

Installation using PVC pipe as the main lateral:

With this layout use the complete assembly pop-up micro sprayers with 1/2" MNPT.  Install the pop-up by installing a PVC tee with 1/2" FNPT and then thread the pop-up into the 1/2" outlet. Mount the pop-up micro sprayer about 2-4” above the ground with spacing between the pop-ups of up to 5’.

 

If using the one piece construction replacement spray head without the pop-up, install the head at the end of a length of 1/4" micro-tubing or use with a semi rigid poly riser.

 

Spray nozzle color: Red, 0.075"

Degrees

Pressure

Flow rate GPM

Radius

360

15

0.45

3.5

360

20

0.52

4.0

360

25

0.57

4.5

360

30

0.63

5.0

  •  

 

Spray nozzle color: Green, 0.06"

Degrees

Pressure

Flow rate GPM

Radius

180

15

0.31

3.5

180

20

0.36

4.0

180

25

0.41

4.5

180

30

0.45

5.0

  •  
  •  

Spray nozzle color: Blue, 0.04"

Degrees

Pressure

Flow rate GPM

Radius

90

15

0.15

3.5

90

20

0.18

4.0

90

25

0.21

4.5

90

30

0.23

5.0