Free shipping on orders $149 $99 & up. exclusions apply

360° Replacement Spray Head for Pop-Up Assembly


360° Replacement Spray Head for Pop-Up Assembly
In Stock

The one-piece construction 360° replacement micro spray head can also be installed at the end of a length of 1/4" micro-tubing or used with a semi rigid poly riser. The micro spray head has a 360° with coverage of up to a 10' full circle and a flow rate of 38 GPH @ 30 PSI.

Part #: MS037
$0.18 ea.

The Drip Store has a wide range of micro sprayers and jets to meet all of today‘s requirements for micro irrigation needs. The no moving parts pop-up micro sprayers can be used for a wide range of applications and are available with 360° 180° and 90° degrees pattern with a small diameter and for watering that requires small droplets size with low precipitation rates. When low volume overhead irrigation is desired for an area where drip emitters are not practical and micro sprinkler diameters and moving parts are not required nor preferred, the micro sprayers may be what are needed. Like micro sprinklers, the pop-up micro sprayers and others are available in a wide variety of styles, flow rates, diameters, and configurations. Like micro sprinklers, they operate at low pressure and require a filter to protect the small orifice of the sprayer from clogging. The main advantage of micro sprayers to some users and installers could be the lack of moving parts and the small to medium sized droplets and coverage.

  • Available: with 1/2" NMPT or assembled with 24” micro tubing and 1/4" Barb
  • Available nozzles : Blue: 90° with 14 GPH @ 30 PSI, Green: 180° with 27 GPH @ 30 PSI , Red: 360° with 38 GPH @ 30 PSI
  • Droplet Size: Medium
  • Flow rate: .15 to .63 GPM
  • Materials: Bases: high impact plastic , Body and piston: Polypropylene , Seals: EPDM and vinyl , Spring: Stainless Steel
  • Nominal operating pressure : 30 PSI
  • Operating pressure: 15 to 35 PSI
  • Pop-up height : 12" or when up 21"
  • Precipitation rate: 2.0 to 2.8 inch/h
  • Recommended filtration: 120 mesh
  • Trajectory Angle: Flat
  • Wetting diameter : up to 5' radius
  • 12" pop-up assembly
  • Available with replacement nozzles
  • Can be installed on any size drip tubing using the micro tubing assembly or mounted to a 1/2" FNPT PVC pipe
  • Install below grade
  • Rugged materials can withstand adverse conditions
  • Unique design incorporates a pressure activated, low friction, upper stem seal and a second stage piston seal to ensure positive sealing

Installation for Pop-up Micro Sprayers

To install the pop-up micro sprayers use one of the two options:

Installation using drip tubing as the main lateral:

With this layout use the complete assembly pop-up micro sprayers with 24” micro tubing and barb. Install the pop-up by punching a hole into the side of the drip tubing and inserting the 1/4" barb into the drip tubing. Mount the pop-up micro sprayer about 2-4” above the ground with spacing between the pop-ups of up to 5’.

Installation using PVC pipe as the main lateral:

With this layout use the complete assembly pop-up micro sprayers with 1/2" MNPT.  Install the pop-up by installing a PVC tee with 1/2" FNPT and then thread the pop-up into the 1/2" outlet. Mount the pop-up micro sprayer about 2-4” above the ground with spacing between the pop-ups of up to 5’.

 

If using the one piece construction replacement spray head without the pop-up, install the head at the end of a length of 1/4" micro-tubing or use with a semi rigid poly riser.

 

Spray nozzle color: Red, 0.075"

Degrees

Pressure

Flow rate GPM

Radius

360

15

0.45

3.5

360

20

0.52

4.0

360

25

0.57

4.5

360

30

0.63

5.0

  •  

 

Spray nozzle color: Green, 0.06"

Degrees

Pressure

Flow rate GPM

Radius

180

15

0.31

3.5

180

20

0.36

4.0

180

25

0.41

4.5

180

30

0.45

5.0

  •  
  •  

Spray nozzle color: Blue, 0.04"

Degrees

Pressure

Flow rate GPM

Radius

90

15

0.15

3.5

90

20

0.18

4.0

90

25

0.21

4.5

90

30

0.23

5.0