24 VAC Actuator for 3/4" and 1" Anti-siphon Valves
SKU
C075
- DESCRIPTION
- SPECIFICATIONS
- FEATURES
- INSTRUCTIONS
- REVIEWS
- The ¾ inch actuator with 24 VAC solenoid model C075 can be used to convert most 3/4 or 1 inch brass or plastic manual anti-siphon valves. Used for drip irrigation or sprinkler system upgrades in residential or commercial applications, and as a cost-effective repair, the C075 actuator is mounted on any manual anti-siphon valve by replacing the top portion on the anti-siphon valve including the manual flow control handle. An anti-siphon valve is used to prevent contaminated water from being siphoned back to the main water supply.
- SPECIFICATION
- • Body Styles: Actuator for ¾ or 1 inch manual anti-siphon valve
- • Size: Factory assembled to fit 3/4" Champion and Orbit manual brass valves with adapter for 1” included in the package. flow control and external manual bleed
- • Operating pressure: 20 to 150 PSI
- • Solenoid: 24 VAC 50/60 Hz
- • Coil resistance @: 68° F 37.5 ohms
- • Holding current: 0.14 Amp @ 50 Hz
- • Inrush current: 0.29 Amp @ 50Hz
- • Power consumption: 1.7/2.2 watts @ 50Hz
- • Temperature range: Up to 130 F
- FEATURES
- Constructed of UV resistant, glass reinforced nylon bonnet with a stainless steel spring
- Factory assembled to fit 3/4" Champion and Orbit manual brass valves with adapter for 1” included in the package.
- The actuator is available with manual flow control and external manual bleed supported by stainless steel screw
- Electric or manual operation
- Flow control handle for water flow adjustment and manual shutoff
- High performance solenoid with low electrical power consumption
- External or internal manual bleed allows quick and easy valve opening and closing
- Anti-siphon valve is used to prevent downstream water from reentering the water supply, especially important when automatically applying fertilizer through a filter
- Use with drip or sprinkler systems
- Normally closed
- Low sensitivity to dirt and voltage fluctuations
- Replaceable plunger tip
- Rugged, with reinforced and supported self-cleaning diaphragm that provides reliable operation even with dirty water
- Smooth valve opening and closing prevents pressure surge hazards:
- INSTRUCTION
The 24 VAC actuator model C075 is factory assembled to fit 3/4" Champion and Orbit manual brass valves. Included in the package you will find a 1"adaptor and seat-washer used to fit 1” Champion and Orbit manual brass valves, 3⁄4" and 1" Rain bird and Rain and 3⁄4" and 1" Orbit plastic valves. The 24 VAC actuator can covert most manual brass or plastic anti-siphon valves to automatic operation.
- Installation
- 1. Shut off the water supply.
- 2. Remove the manual stem from the existing valve. If you are converting an anti-siphon valve, temporarily remove the anti-siphon cap (you will need to install the actuator and the cap together).
- 3. Replace any existing worn washers with the new ones provided.
- 4. Install the actuator into the manual valve, using a wrench, tighten firmly, but do not over tighten.
- 5. Rotate the flow control clockwise until completely closed.
- 6. Turn on the main water supply.
- 7. Test the actuator by turning the solenoid counter clock wise one to two turns or by using the screw bleed located on top of the valve.
- 8. Now, rotate the flow control counter clockwise, one turn at the time until the valve is operational and all sprinklers/sprayers working evenly and to your satisfaction.
- 9.Turn the actuator off by turning the solenoid few turns clock wise to close or by turning off the screw bleed
- Note: If water continue to flow, turn the flow control clockwise 1⁄4 turn each time. Repeat steps 5-9 if necessary.
- 10. Use 16, 18 or 20-gauge direct burial, strand gauge sprinkler wire between the valve location and the AC controller used.
- 11. Connects each valve to the AC controller using two wires with the hot wire is color-code and the common wire is white. The common wire (white) is shared with all valves.
- 12. Connect the common wire to either solenoid wire of all valves using waterproof wire splice connectors.
- 13. Connect each color code wire to the remaining wire of each valve using waterproof wire splice connections.
Write A Review For 24 VAC Actuator for 3/4" and 1" Anti-siphon Valves
